Features

• IntelliDose™ controls your nutrient and pH levels for you, on demand. 
• Doses up to an eight-part nutrient recipe, with the ability to program adjustable ratios for each of the parts.
• As plants consume nutrients, NutriDose compensates by adding more nutrient concentrate.
• As water levels decrease, NutriDose can balance the ion ratios in your reservoir by adding water (with installed float valve).
• Measures in 3 scales, CF, EC or PPM, and can measure from .1 to 99.9 CF / 0-4999 PPM.
• Constantly measures pH and adjusts accordingly, either up or down.
• Quick and easy pH and Conductivity calibration helps ensure proper measurements.
• Monitor and control the IntelliDose using your PC or laptop (certain requirements apply) with the supplied USB cable and software.
• On-screen displays make your PC or laptop an incredibly informative console for control of your NutriDose and nutrient tank.
• Utilize the data logging feature to track the nutrient uptake, pH fluctuations and temperature changes
• Set the alarm for a phone alert via PC modem if something goes wrong
• Designate different ratios of your A, B and C nutrients for exact measurements
• Automatically adjust your nutrient levels between day and night

Specifications

• Outputs:
  Eight (8), 12V DC
• Nutrient measurement units:
  EC, CF or TDS (EC x 500)
• Measured range:
  EC: 0.00 to 9.99
  CF: 0.1 to 99.9
  PPM: 0 to 1999
• Nutrient resolution:
  0.01 mS/cm
  0.1 CF
• Nutrient measurement accuracy (temperature compensated):
  +/- 0.1 EC
  +/- 1.0 CF
  +/- 10 ppm
• Nutrient dosing range:
  EC: 0.00 to 5.99
  CF: 0.1 to 59.9
  PPM:  0 to 1190
• pH resolution and accuracy:
  – 0.1 pH
• pH measurement range:
  2 pH to 12 pH
• pH dosing range:
  5 to 7 pH
• Nutrient and pH dosing times:
  Settable from 1 second to 30 seconds
• Dosing interval:
  Settable from 0 minutes (continuous dosing) to 30 minutes
• Dosing operates valves sequentially to reduce power surge
• Temperature resolution and accuracy:
  +/-1° C
  +/-2° F
• Temperature measurement range:
  0-50 °C
  32-125 °F
• Operating temperature range:
  0-50° C
  32-125° F
  (and not in direct sunlight)
• Power source:
  12 volt AC transformer pack supplied. Outputs will have the same voltage as the supplied voltage from the power pack.
• Large graphics display using simple four key interface (similar to cell phone key operation)
• Nutrient sensor uses DiPulse™ technique to resist fouling
• Dosing shut-off:
  • if nutrient is below 0.1 EC, 1 CF, 10 PPM
  • if pH is below 4.5 or above 8.0
  • if dosing effect is counterintuitive, i.e. by dosing pH lower the measured pH goes up
  • if sensor fault detected
• Supplied with PC software and 5 meter USB cable
• Can also be supplied with solenoid valve kit or peristaltic pump kit

Options and Accessories

Ordering an IntelliDose? Make sure you have everything
you need…

IntelliDose Complete comes with the following:
IntelliDose Controller
Sample Pot
pH Probe
PPM Probe
Power Supply
USB Cable (15‘)
Instruction Booklet
Software
All mounting hardware and necessary tubing and
fittings

Do you need Solenoids or Peristaltic Pumps ?

Solenoids are gravity fed, meaning you mount the stock tanks on a shelf above the unit. Peristaltic Pumps do not need to be gravity fed, so your stock tanks can be on the floor, especially necessary if you have large stock tanks.

Do you need Stock Tank Kits or Tank Fitting Kits ?

Our Stock Tank Kits come with a bucket, lid, tank fitting and tubing. If you have your own buckets and tubing, a Tank Fitting Kit is all you need. You will need one Stock Tank Kit or one Tank Fitting Kit for each nutrient and/or pH solution.

Do you need a Twin Relay Box ?

If you would like to use the irrigation feature of the IntelliDose, whether to run your system pump or to run a pump to empty your reservoir, you will need a Twin Relay Box.

Downloads

Information Downloads
	Download Intellidose Data Sheet (234 kb)
	Download Intellidose Product Instructions (412 kb)